ABOUT

Solutions & Cases

Our Case
  • Aggregate Crushing Value Civil Engineering

    AGGREGATE CRUSHING VALUE This test helps to determine the aggregate crushing value of coarse aggregates as per IS: 2386 (Part IV) 1963. The apparatus used is Cylindrical measure and plunger, Compression testing machine, IS Sieves of sizes 12.5mm, 10mm and 2.36mm

  • Aggregate Crushing Value Test -Determine Aggregate

    Aggregate crushing value test on coarse aggregates gives a relative measure of the resistance of an aggregate crushing under gradually applied compressive load. Coarse aggregate crushing value is the percentage by weight of the crushed material obtained when test aggregates are subjected to a specified load under standardized conditions.

  • IS 2386-4 (1963): Methods of test for aggregates for

    aggregate crushing value of coarse aggregate. NOTE 1 -The ‘aggregate crushing value’ gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. With aggre- gate of ‘aggregate crushing value’ 30 or

  • Aggregate Crushing Value Test YouTube

    Mar 24, 2013· Aggregate Crushing Value /CrushingTest of Coarse Aggregate Duration: 10:02. SPECIFIC GRAVITY AND WATER ABSORPTION TEST AS PER IS:2386-PART-3 Duration: 6:46. ravi parikh 41,720 views.

  • Aggregate Crushing Value Test Determine Aggregate

    The table given below lays down specified limits of per cent aggregate crushing value, for different types of road construction. Table3. The specified limits of pe cent aggregate crushing value. Note:- For strong aggregate, crushing value should be low. For surface courses this value should not exceed more than 30% and for courses not more than

  • DETERMINATION OF AGGREGATE CRUSHING VALUE

    aggregate to crushing under a gradually applied compressive load. Crushing value is a measure of the strength of the aggregate. The aggregates should therefore have minimum crushing value. 3. APPARATUS The apparatus of the aggregate crushing value test as per

  • Crushing value apparatus (ACV), Aggregates testing

    The aggregate crushing value (ACV) provides relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Two versions available: 150 (standard) and 75 mm dia. The apparatus comprehend cylinder, plunger, base plate, tamping rod and measure. Cylinder, plunger and base plate are made from special alloy

  • Aggregate Crushing Value As Per Astm FTMLIE Heavy Machinery

    Aggregate Crushing Value As Per Astm. Aggregate crushing value is a numerical index of the strength of the aggregate and it is used in construction of roads and pavements Crushing value of aggregates indicates its strength Lower crushing value is recommended for roads and pavements as it indicates a lower crushed fraction under load and would give a longer service life and a more

  • CIVIL QUALITY CONTROL LAB: AGGREGATE CRUSHING VALUE

    The aggregate crushing value is defined, as a ratio of the weight of fines passing the specified IS sieve to the total weight of the sample expressed as a percentage. 100 W2 Where, W1 =

  • Aggregate crushing value of aggregates with cement

    BS 812 part 110 describes a method to determine the aggregate crushing value (ACV) which gives a relative measure of the crushing resistance of aggregate under an increasing compressive load.The

  • Impact and Crushing Value PCTE

    Impact and Crushing Value Aggregate Crushing Value (ACV) Sets. UTA-0630 Aggregate Crushing Value (ACV) Set Ø 150 mm BS. UTA-0640 Aggregate Crushing Value (ACV) Set Ø 75 mm BS. The Aggregate Crushing Value (ACV) Test Set measures how resistant an aggregate

  • 2020 Gravel Prices Crushed Stone Cost (Per Ton, Yard & Load)

    Gravel Cost Per Square Foot. Gravel costs $0.50 to $2.50 per square foot on average when covering an area 12" deep (a cubic foot), depending on the type. Base gravel, crusher run, slate, shale, and crushed concrete are the cheapest at $0.50 to $1.50 per square foot, while colored and decorative gravel run $3 per

  • 7.7 Aggregate Crushing Value and 10% Fines Value 7.7.1

    number. Report the mean as the Aggregate Crushing Value, unless the individual results differ by more than 0.07 times the mean value. In this case repeat the test on two further specimens, calculate the median of the four results to the nearest whole number and report the median as the Aggregate Crushing Value

  • Aggregate Crushing Value test we civil engineers

    Jan 23, 2018· AIM: To determine the aggregate crushing value of coarse aggregates as per IS: 2386 (Part IV) 1963. APPARATUS: i) Cylindrical measure and plunger ii) Compression testing machine iii)

  • How to Determine the Aggregate Crushing Strength Value in

    Calculation of aggregate crushing value. The aggregate crushing value is defined as the ratio of the weight of fines passing through specified IS (here 2.36mm sieve) to the total weight of sample

  • Aggregate: Mechanical Properties of Aggregate Concrete

    The weight of aggregate that would fill a container of unit volume is known as bulk density of aggregate. Its value for different materials as per concrete hand book CIA Bombay is shown in Table 4.10. Voids: With respect to a mass of aggregate, the term voids refers to the space between the aggregate

  • IS 383 (1970): Specification for Coarse and Fine

    2.1.2 Crushed Stone Sand Fine aggregate produced by crushing hard stone. 2.1.3 Crushed Grace1 Sand line aggregate produced by crushing natural gravel. . 2.2 Coarse Aggregate -- Aggregate

  • AGGREGATE CRUSHING VALUE (IS:2386-Part 4-1963)

    May 08, 2013· Objective For determination of the aggregate crushing value of coarse aggregate, which passes 12.5 mm. IS sieve and retained on 10 mm. IS sieve. Reference Standard IS: 2386 (Part IV)-1963 Methods of test for aggregate

  • BS 812-112:1990 Testing aggregates. Method for

    Methods for determination of aggregate crushing value (ACV) BS 812-111:1990 Testing aggregates. Methods for determination of ten per cent fines value (TFV) BS EN 12350-4:2019 TC Tracked